Processing common sense
Factors Affecting Billet Trimming Ratio
Factors Influencing the Jumbo head and tail Yield of Billet Cutting
Introduction
The yield rate of jumbo head and tail of billet cutting is a very important factor in the steel making industry, because it directly affects the production cost and efficiency. It is also an important indicator of pr......
1071 
Sophie
Special processing
Special machining is a sophisticated and advanced form of machining that typically involves custom-made production parts and components. This form of machining offers a variety of benefits for customers, including precision and accuracy, high-quality results, and less material waste. Special machi......
The basic principle of the fluidized bed method
Introduction
Influidized bed technology is a type of thermal sludge treatment process. This type of technology is commonly used for the treatment of municipal, agricultural and industrial waste. It has been applied for treating many materials such as sludge, wastewater, hazardous waste, industria......
The Method of Realizing Multi-scale Optimal Cutting
Introduction
The process of cutting materials is an important step in many industries, where it is often necessary to cut complex shapes in large sheet materials. An essential component of the cutting process is the optimization of cutting paths. The most common approach is to use software to gen......
Matters needing attention in adjusting the roll clearance of high-speed rolling mill
Adjustment of The Inter-Roll Gap of the High-Wire Rolling Mill
1. Introduction
The high-wire rolling mill is a key equipment for continuous production of strip in order to meet the needs of modern industry for high-precision, high-efficiency and large-scale production of thin strip. The adjustme......
Influencing factors of rolling pressure
？
The Influence Factors of Rolling Pressure
Rolling is a process that involves putting a metal component in direct contact with a rolling system such as a roll press. The roll press presses the component against a certain pressure in order to form the component into a desired shape or form. Rolli......
Generation and prevention of wire cracks
Crack in Wire and How to Prevent It
Cracks in wire can occur during the manufacture, operation, or storage of the wire. During the manufacture of wire, the wire is drawn or extruded through dies that put pressure on the wire, resulting in cracks and splits. During operation, wire fatigue can occu......
The treatment method of sticky steel
Sticky Steel Treatment
Sticky steel is a particular type of steel formation that occurs during the manufacturing process, in which the two layers of steel fuse together to form imperceptible bond. It is normally found in rolled steel products, like rods and sheet metal that are used for construct......
Steel pressure processing method
Processing of Steel by Pressure
Steel is a metal alloy made of iron and carbon, with other elements added to achieve certain desired properties. It is one of the strongest and most widely used materials in modern life. Steel is used in a wide range of applications, including construction, automot......
Forging performance test
The impact test is the most commonly used metallurgical performance test of forged parts. It is used to analyze the work hardening level, the distribution and shape of the residual austenite grains, the amount and characteristics of the retained austenite, and the mechanical properties of the micr......
Popular Entries
- General content of hydrogen and nitrogen in steels melted in open hearth and electric arc furnaces
- Deformation of the metal cutting layer
- New Development of Stamping Process in Automobile Manufacturing Technology
- The perfect combination of water cutting and laser cutting
- Steel is divided according to the carbon content according to the characteristics of converter smelting
- Technology of cold extruding small thread bottom hole
- Casting Technology of Killed Steel Die Casting
- Comparison of the new and old national standard thread tolerance zone positions
- Characteristics of Welding Heat Affected Zone of Easy Quenching Steel
- Approximate indexing table in the dividing head in milling (the fixed number of dividing head is 40)
- Compound extrusion
- Rolled piece size measurement
- Bismuth based solder
- wheel balance
- gas counterflow
Recent Updates
- Quantity and installation position of gas supply components at the bottom of re-blowing converter
- Structural safety impact of stamping dies
- fibrous tissue
- Approximate indexing table in the dividing head in milling (the fixed number of dividing head is 40)
- Selection and Application of Air Supply Source at the Bottom of Combined Blowing Converter
- Maintenance essentials of stamping die
- tension straightening
- Foam problem of cutting fluid
- Maintenance of the bottom gas supply element of the re-blown converter
- Safety requirements for stamping dies
- Brazing
- Development of new steel grades and their weldability in my country
- additional stress
- Stamping noun terminology
- TIG welding
- Requirements for maintenance technical data of CNC machine tools
Trending Keywords
Copyright © 2016 - 2024 by metal-knowledge.com. All rights reserved